Search
Filters
Close

Tikka T3 Pre-Fit Barrel

Affordable precision barrel for your Tikka T3 rifle. Please read product overview below barrel options for important additional details.
*
*
*
*
*
*
*

Polish or Matte

(Matte is media blasted only!)

Cryogenics

-priority tasking (typically shaves off 20%-50% of lead time--cannot be added after order is placed).

Ship to
*
*
Shipping Method
Name
Estimated Delivery
Price
No shipping options
$482.00

Tikka T3 Pre-Fit Barrels

If you are gun-savy and have a barrel vise, a 3/8" square drive torque wrench, "crow's foot" barrel nut wrench and barrel nut as well as the corresponding chambers’ Go gauge, you have everything you need to correctly install a barrel for your Tikka T3 rifle.  

Barrel nut required, not included.

Recommended OEM barrel nut torque specs: 35-45 ft/lbs.

Please check our Frequently Asked Questions for our current lead times.

Need a Tikka T3 barrel nut? Head here!

Need a Muzzle Thread Protector?  Head here!

No Shipping outside the US

*Please refer to the footer of this page for up-to-date production lead-time estimates.

Fluting: Adds 1 week to order lead time

 

Our Prefit 1MOA accuracy guarantee is 3 rounds at 100 yards with quality ammo and a skilled shooter. Like anything X-Caliber makes, we stand behind it 100%. If you do not think your barrel can shoot 1MOA groups or less, we will have you ship it back. We will inspect the barrel. If the barrel fails, we will build you another barrel and ship it to you at no cost. If the barrel passes all test, it will be shipped back to you at your expense.

For more information about our 1MOA accuracy guarantee and the conditions that apply, please refer to our FAQ or Conditions Pages.

 

For more information on available contours, please visit our Contours page.

 

***************************

 

X-Caliber Barrel Break-In

Procedure Guide

 

When breaking in your new X-Caliber Barrel, you should perform appropriate fire and clean cycles to normalize the bore surface. Each fire and clean cycle consists of a certain number of rounds fired (one to five) followed by a cleaning procedure (see below for reference), to be completed a certain number of times (1-25). These vary depending on the type of steel of the barrel, bore/groove diameter, velocity and pressure of any given round, etc. This is to be used as a guide. Since our barrels are hand-lapped, each barrel may break in a little differently. Some barrels may require more or less shots or cycles to break in than what is listed here.

 

416R Stainless Steel: Fire One Round then Clean: Do this 5-10 times. Fire Three Times then Clean: Do this 1 time. Fire Five Times then Clean: Do this 1 time.

4140 Chrome Moly: Fire Once Round then Clean: Do this 5-25 times. Fire Three Times then Clean: Do this 2 times. Fire Five Times then Clean: Do this 1 time.

 

 Example: For a 416R Stainless Steel barrel, you would fire one round, then perform the cleaning steps outlined below a total of five to ten times (shoot 1 round & clean, done 5-10 times) before starting the three shot cycle where you would fire three rounds and then clean as outlined below, then proceed to fire five rounds then clean, completing the break-in procedure.

 

Each Firing Cycle (1 shot, 3 shot or 5 shot) should be followed by cleaning the bore (see steps below for reference):

 

1.)    Using a one-piece, coated cleaning rod with a properly sized bore brush (wet with your favorite non-foaming bore solvent), carefully clean the bore from the chamber end toward the muzzle (3-5 passes is usually sufficient). If you cannot clean from the chamber end, be sure to use a bore-guide so as not to damage the crown or muzzle end of the rifling. Let sit 30-60 seconds before moving on to the next step.

2.)    Push a dry patch down the bore. (2-3 times)

3.)    Put a few of drops of oil on a patch and push that down the bore so as to leave a thin film of oil inside the bore.

4.)    Begin a new cycle: Fire your next round or rounds in your next firing cycle and repeat cleaning as necessary.

  

It is recommended to keep a written tally of your current step within the process so if you get distracted you will know where you left off.

 

Tikka T3 Pre-Fit Barrels

If you are gun-savy and have a barrel vise, a 3/8" square drive torque wrench, "crow's foot" barrel nut wrench and barrel nut as well as the corresponding chambers’ Go gauge, you have everything you need to correctly install a barrel for your Tikka T3 rifle.  

Barrel nut required, not included.

Recommended OEM barrel nut torque specs: 35-45 ft/lbs.

Please check our Frequently Asked Questions for our current lead times.

Need a Tikka T3 barrel nut? Head here!

Need a Muzzle Thread Protector?  Head here!

No Shipping outside the US

*Please refer to the footer of this page for up-to-date production lead-time estimates.

Fluting: Adds 1 week to order lead time

 

Our Prefit 1MOA accuracy guarantee is 3 rounds at 100 yards with quality ammo and a skilled shooter. Like anything X-Caliber makes, we stand behind it 100%. If you do not think your barrel can shoot 1MOA groups or less, we will have you ship it back. We will inspect the barrel. If the barrel fails, we will build you another barrel and ship it to you at no cost. If the barrel passes all test, it will be shipped back to you at your expense.

For more information about our 1MOA accuracy guarantee and the conditions that apply, please refer to our FAQ or Conditions Pages.

 

For more information on available contours, please visit our Contours page.

 

***************************

 

X-Caliber Barrel Break-In

Procedure Guide

 

When breaking in your new X-Caliber Barrel, you should perform appropriate fire and clean cycles to normalize the bore surface. Each fire and clean cycle consists of a certain number of rounds fired (one to five) followed by a cleaning procedure (see below for reference), to be completed a certain number of times (1-25). These vary depending on the type of steel of the barrel, bore/groove diameter, velocity and pressure of any given round, etc. This is to be used as a guide. Since our barrels are hand-lapped, each barrel may break in a little differently. Some barrels may require more or less shots or cycles to break in than what is listed here.

 

416R Stainless Steel: Fire One Round then Clean: Do this 5-10 times. Fire Three Times then Clean: Do this 1 time. Fire Five Times then Clean: Do this 1 time.

4140 Chrome Moly: Fire Once Round then Clean: Do this 5-25 times. Fire Three Times then Clean: Do this 2 times. Fire Five Times then Clean: Do this 1 time.

 

 Example: For a 416R Stainless Steel barrel, you would fire one round, then perform the cleaning steps outlined below a total of five to ten times (shoot 1 round & clean, done 5-10 times) before starting the three shot cycle where you would fire three rounds and then clean as outlined below, then proceed to fire five rounds then clean, completing the break-in procedure.

 

Each Firing Cycle (1 shot, 3 shot or 5 shot) should be followed by cleaning the bore (see steps below for reference):

 

1.)    Using a one-piece, coated cleaning rod with a properly sized bore brush (wet with your favorite non-foaming bore solvent), carefully clean the bore from the chamber end toward the muzzle (3-5 passes is usually sufficient). If you cannot clean from the chamber end, be sure to use a bore-guide so as not to damage the crown or muzzle end of the rifling. Let sit 30-60 seconds before moving on to the next step.

2.)    Push a dry patch down the bore. (2-3 times)

3.)    Put a few of drops of oil on a patch and push that down the bore so as to leave a thin film of oil inside the bore.

4.)    Begin a new cycle: Fire your next round or rounds in your next firing cycle and repeat cleaning as necessary.

  

It is recommended to keep a written tally of your current step within the process so if you get distracted you will know where you left off.

 

Write your own review
  • Only registered users can write reviews
*
*
Bad
Excellent
*
*
*
*
Customers who bought this item also bought

Barrel Nuts for Shoulderless Prefit Barrels

Stainless Steel Barrel Nuts made by Triune Precision. Available for Savage Small Shank, Remington 700 "Rem/Age", Bighorn, Mossberg Standard Action, Mossberg Small/Mini Action, Remington 783 or Ruger American. RemAge, Savage/Mossberg Standard, Ruger/Tikka nuts use 1-1/4" wrench. Mossberg Small/Mini nut uses 1-1/8" wrench.
$36.00

Muzzle Thread Protector

Cover and protect exposed muzzle threads with one of our X-Caliber Thread Protectors. Available in 3 sizes. Thread availability listed per size.
$30.00

X-Terminator Muzzle Brakes

Extreme recoil reduction muzzle brake. Length: 2 1/2". Diameter: .980" -- Specified Caliber options will include a slight increase in actual diameter to allow for safe margins with passing projectiles.
$90.00